Showing 1–20 of 63 results
R6 over axle adapter is used to press R6 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing. Machined, red or gray anodized aluminum
6900 over axle adapter is used to press 6900 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
6900 over axle adapter is used to press 6900 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Our 6900 open bore adapter, also referred to as a drift, is used to press 6900 sealed bearings into hub shells or suspension components.
Our 6801 open bore adapter is used to press 6801 sealed bearings. The adapter is machined with one step at 11.9mm OD, which fits into the center of the sealed bearing.
Our 6801 over axle adapter is used to press 6801 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Our 6901 open bore adapter is used to press 6901 sealed bearings. The adapter is machined with one step at 11.9mm OD, which fits into the center of the sealed bearing.
Our 6901 over axle adapter is used to press 6901 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Our 6802 open bore adapter is used to press 6802 sealed bearings. The adapter is machined with one step at 14.9mm OD, which fits into the center of the sealed bearing.
Our 1526 open bore adapter is used to press 15×26 sealed bearings. The adapter is machined with one step at 15mm OD, which fits into the center of the sealed bearing.
Our 6002 open bore adapter is used to press 32×15 sealed bearings. The adapter is machined with one step at 15mm OD, which fits into the center of the sealed bearing.
Our 6002 over axle adapter is used to press 6002 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Our 6803 open bore adapter is used to press 26×17 sealed bearings. The adapter is machined with one step at 17mm OD, which fits into the center of the sealed bearing.
Our 1728 open bore adapter is used to press 17×28 sealed bearings. The adapter is machined with one step at 27mm OD, which fits in to the center of the sealed bearing.
Our 6003 open bore adapter is used to press 35×17 sealed bearings. The adapter is machined with one step at 17mm OD, which fits into the center of the sealed bearing.
Our 6003 over axle adapter is used to press 6003 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Our 6904 open bore adapter is used to press 37×20 sealed bearings. The adapter is machined with one step at 20mm OD, which fits into the center of the sealed bearing.
Our 6904 over axle adapter is used to press 6904 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Sealed bearing extractor for 22mm ID (GXP) bearings. Extractor has 1/2″ thru hole for use with our 1/2″ threaded rod press handles.
Sealed bearing extractor for 24mm ID bearings. Extractor has 1/2″ thru hole for use with our 1/2″ threaded rod press handles.
No products in the cart.