Showing 41–60 of 62 results
Our BB30-OUT open bore adapter, also referred to as a drift, is used to press BB30-OUT cups in to your frame. The adapter is machined with two steps: one at 24mm OD slips in to the center of the sealed bearing, and a larger step at 42mm OD to fit the frame’s BB shell.
Note: Discontinued item. Sold as-is. No returns.
Another must-have tool for the busy bike shop. Our machined aluminum Speed Spacers take up extra space on our bearing presses so you don’t need to spin the handles as far to tighten things up. The bearing press speed spacer 10mm.
Another must-have tool for the busy bike shop. Our machined aluminum Speed Spacers take up extra space on our bearing presses so you don’t need to spin the handles as far to tighten things up. They also work in axle configurations where you need to press in a bearing over an axle.
Another must-have tool for the busy bike shop. Our machined aluminum Speed Spacers take up extra space on our bearing presses so you don’t need to spin the handles as far to tighten things up. 20mm thru hole size makes this perfect for use on hubs with larger axles.
Another must-have tool for the busy bike shop. Our machined aluminum Speed Spacers take up extra space on our bearing presses so you don’t need to spin the handles as far to tighten things up. They also work in axle configurations where you need to press in a bearing over an axle.
Frame linkage standoff works with our bearing press handles as a spacer to allow the press handles to fully seat bearings over suspension linkages that protrude beyond the face of the bearing.
Our GXP-LEFT open bore adapter is used to press 22×37 sealed bearings in to SRAM GXP bottom bracket cups and direct fit frames like TREK BB90. The adapter is machined with one step at 22mm OD, which fits in to the center of the sealed bearing.
Headtube drifts for use with the Wheels Mfg Headset Cup Press. 1/2″ thru hole. Drift is machined with multiple steps to fit common head tube inner diameters listed below. Not recommended for use with Wheels Mfg PRESS-1 or PRESS-4 handles and rod, which have a smaller 3/8″ diameter rod.
Our 6000 open bore adapter, also referred to as a drift, is used to press 6000 sealed bearings.
Our 6001 open bore adapter is used to press 28×12 sealed bearings. The adapter is machined with one step at 12mm OD, which fits in to the center of the sealed bearing.
Our 6802 open bore adapter is used to press 24×15 sealed bearings. The adapter is machined with one step at 15mm OD, which fits in to the center of the sealed bearing.
Our 6900 open bore adapter is used to press 6900 sealed bearings. The adapter is machined with one step at 9.9mm OD, which fits into the center of the sealed bearing.
Our 6901 open bore adapter is used to press 24×12 sealed bearings. The adapter is machined with one step at 12mm OD, which fits in to the center of the sealed bearing.
Our 6903 open bore adapter is used to press 30×17 sealed bearings. The adapter is machined with one step at 17mm OD, which fits in to the center of the sealed bearing.
These drifts are spares for your most commonly used bearing sizes. They’re also an excellent addition to the Press-4
Our 6001 over axle adapter is used to press 6001 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Our 6802 over axle adapter is used to press 6802 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Our 6901 over axle adapter is used to press 6901 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing
Our 6903 over axle adapter is used to press 6903 sealed bearings into hub shells or suspension components. An over axle adapter is necessary when the bearing slides over the axle before it is pressed into the hub shell or suspension component. In addition to the adapter, you often need spacers to clear the end of the axle and allow enough clearance for the press to fully push in the bearing.
Replacement 3/8″ x 3″ plastic dowels for our Large Sealed Bearing Press (PRESS-1).
No products in the cart.